Chrysler 3.3 & 3.8 engine

src: upload.wikimedia.org

This engine was Chrysler's first 60° V6 engine designed and built in-house for front wheel drive vehicles, and their first V6 not based on a V8. It was designed as a larger, more powerful option to the Mitsubishi 3.0 V6 in the minivans and debuted in 1990.

The engine has been produced in two major variants differing by their piston displacement: a 3.3 l (201 cu in) and a 3.8 l (232 cu in). The 3.3 was dropped after 2010 with the Chrysler minivans, and the 3.8 was dropped after 2011 with the Jeep Wrangler, ending 21 years in production.

Video Chrysler 3.3 & 3.8 engine

Specifications

Maps Chrysler 3.3 & 3.8 engine

History

The original 3.3 engine, as well as the larger 3.8, are pushrod engine designs. The 3.3 was introduced in 1990 with the Chrysler Imperial, New Yorker, and related K-series models, and was joined in 1991 by the 3.8. Production on the 3.3 was stopped in 2010 after a run of 5,076,603 engines, while the 3.8 remained in production until May 2011 in Trenton, Michigan for the Jeep Wrangler. Both use a cast iron block and aluminum heads.

3.3

The first of the family, the 3.3 liter engine's actual piston displacement is 3,301 cc (201 cu in) with a 93 mm (3.7 in) bore and 81 mm (3.2 in) stroke. In 1994, the 3.3 received a 12 hp (8.9 kW) increase in power to 162 hp (121 kW) due to a new air intake. In 2001, the engine was fitted with a variable intake control system which boosted output to 180 hp (130 kW) at 5000 rpm and 210 lb?ft (285 N?m) at 4000 rpm. The engine was especially suited for transverse applications in Chrysler's minivans, but was also used in a longitudinal front-wheel-drive setup on 1993-1997 LH platform cars. It was last used in 2010 for Chrysler minivans before the introduction of the new 3.6 L Pentastar engine for the 2011 model year.

Designated EGA, the 3.3 was built at Trenton Engine in Trenton, Michigan. It uses SFI fuel injection, has roller tappets and features forged steel connecting rods, a one-piece cast camshaft, and either a cast aluminum or reinforced plastic intake manifold. The 3.3 has a timing chain, and is an interference engine meaning that the valves will collide with the pistons in the event of a timing chain failure.

Vehicles using the 3.3 include:

• 1990-1993 Dodge Dynasty, Chrysler New Yorker, Chrysler Imperial, (replaced the 3.0 L Mitsubishi 6G72 engine)
• 1990-2010 Chrysler minivans
• 1993-1997 Chrysler Concorde/Dodge Intrepid/Eagle Vision

3.8

The 3.3 was bored to 3.78 in (96 mm) and stroked to 3.43 in (87 mm) to create a 3,778 cc (231 cu in) version. This EGH version was also built at Trenton Engine in Trenton, MI.

The 3.8 received an increase in power of 12 hp (9 kW), for a total of 162 hp (121 kW) in 1994 via a new intake system. In 1998 the compression ratio increased for a total of 180 hp (134 kW) and 240 lb?ft (325 N?m). In 2001, like the 3.3 the 3.8 received the symmetrical reinforced plastic intake plenum and revised camshaft which boosted output to 215 hp (160 kW) at 5000 rpm with 245 lb?ft (332 N?m) at 4000 rpm.

Vehicles using the 3.8 include:

• 1991-1993 Chrysler New Yorker and Chrysler Imperial 150 hp (112 kW), 213 lb·ft (289 N·m)
• 1994-2010 Chrysler minivans
• 2004-2007 Chrysler Pacifica (CS)
• 2007-2011 Jeep Wrangler
• 2009-2010 Volkswagen Routan

src: images.gtcarlot.com

SOHC

A single overhead camshaft was an addition to the lineup for 1993. Introduced with the 3.5 L engine, this design spawned the DOHC 2.7 L Chrysler LH engine, as well as the 3.2 L and 4.0 L variants.

src: upload.wikimedia.org

References

• "Chrysler/Dodge 3.3". Allpar.com. Retrieved February 6, 2006. 
• "The 2.7, 3.2, and 3.5  L engines". Allpar.com. Retrieved February 6, 2006. 

src: www.moibbk.com

See also

• List of Chrysler engines

Source of the article : Wikipedia